Motor
Rotate the motor(HS-010-1V)
Working principle and structure
Motor into the oil: Pump oil pressure regulator by the pressure relief valve, through the 3-way 4-way solenoid valve on the right after (PA), through one-way throttle valve into the right side of the motor, the motor clamping or loosening. Return the oil on the left side of the motor through the left one-way throttle to the 3-position 4-way solenoid (BT) and back to the tank through the one-way throttle. When the solenoid valve is reversed, the pump oil through the relief valve into the left side of the motor, the motor clamp or release.
Working oil
Low condensate hydraulic oil or anti-vibration hydraulic oil is recommended. Normal working oil temperature is 15C-65C and oil cleanliness is controlled within NAS10 level.
NL-type internal tooth-shaped flexible coupling(NL1-NL10)
Introduction
NL-type internal gear coupling is the latest domestic product, has been widely adopted in foreign countries, the product is suitable for flexible transmission between the shaft, allowing greater axial, radial displacement and angular displacement, and has the structure The utility model has the advantages of simple, convenient maintenance, easy disassembly and assembly, low noise, small transmission power loss and long service life. The utility model has been widely used in forging machine, casting equipment, plastic, mine, building material, food, Leather, textile, fan, pump and other industries. As it is superior to all other aspects of the coupling so much the user is welcome.
Shaft hole type cylindrical (Y), round push (Z) and short cylindrical (J), shaft hole and keyway according to the national standard GB3852-83 "coupling shaft hole and keyway type and size" requirement. Working temperature is -20 ℃ ~ +70 ℃.
Half couplings are made of HT250 cast iron, and the inner toothed coupling elastomer jacket is made of fiber-reinforced nylon elastomer.
NL type internal tooth shape flexible coupling graph and symbol
NL-type internal tooth-shaped flexible coupling basic parameters and dimensions
| Model |
Nominal torque (N.m) |
Permissible speed (r.min) |
Main dimensions | Allow installation size deviation |
Inertial torque (kg.㎡) |
quality (kg) |
||||||||
|
Shaft hole diameter d1-d2 |
Half shaft length L1-L2 |
Total length L(L1+L2+L3) |
D | D1D2 | E | L3 |
Axial (mm) |
Radial (mm) |
angle a° | |||||
| NL1 | 40 | 6000 | 6-14 | 20-32 | 36-68 | 40 | 26 | 4 | 34 | 2 | ±0.3 | 1 | 0.25 | 0.6 |
| NL2 | 100 | 6000 | 10-22 | 25-50 | 54-104 | 52 | 36 | 4 | 40 | 2 | ±0.4 | 1 | 0.92 | 1.1 |
| NL3 | 160 | 6000 | 12-25 | 30-60 | 64-124 | 66 | 44 | 4 | 44 | 2 | ±0.4 | 1 | 3.10 | 1.9 |
| NL4 | 250 | 6000 | 14-35 | 35-80 | 74-164 | 83 | 58 | 4 | 48 | 2 | ±0.4 | 1 | 8.69 | 2.6 |
| NL5 | 315 | 5000 | 16-40 | 40-110 | 84-224 | 98 | 68 | 4 | 50 | 3 | ±0.4 | 2 | 14.20 | 3.9 |
| NL6 | 400 | 5000 | 20-42 | 40-110 | 84-224 | 100 | 68 | 4 | 54 | 3 | ±0.4 | 2 | 18.34 | 5.3 |
| NL7 | 630 | 3600 | 24-50 | 45-120 | 92-224 | 115 | 80 | 4 | 60 | 3 | ±0.6 | 2 | 56.5 | 8.2 |
| NL8 | 1250 | 3600 | 28-60 | 50-140 | 114-284 | 140 | 96 | 6 | 74 | 3 | ±0.6 | 2 | 98.55 | 19.5 |
| NL9 | 2000 | 2000 | 30-75 | 60-170 | 126-346 | 175 | 124 | 9 | 92 | 4 | ±0.7 | 2 | 370.5 | 28 |
| NL10 | 3150 | 1800 | 40-95 | 70-210 | 148-428 | 220 | 157 | 9 | 100 | 4 | ±0.7 | 2 | 1156.8 | 49 |
Ordering mark method
| Example 1: NL5 tooth-shaped flexible coupling |
|
Example 2: NL8 internal tooth-shaped flexible coupling | Mark as | ||||
| Active side: Y-axis hole, A keyway,d1=30,L1=80 | NL5 | YA30×80 | Active side: Z-axis hole, C-keyway,d1=48,L1=110 | NL8 | ZC48×110 | ||
| Slave: Y-axis hole, A-type keyway,d2=38,L2=80 | YA38×80 |
|
JB60×140 | ||||
| *Note: The user does not specify the material are castings HT250 supply | |||||||
Rotate the motor(HS-010-1V)
Use
Gao Hao brand HS-010-1V rotating motor (also known as the guide motor), the use of gap-sealed structure, with a simple structure, small size, light weight, long life and other characteristics suitable for storage, lifting, port hydraulic transmission system .
Model Description
Outline drawing and connection dimensions
|
The maximum allowable internal bypass leakage value (PSI) |
0-1000 | 1000-2000 | 2000-3000 | |||||||||||||||
| 2000cc per min | 2500cc per min |
0cc per min |
||||||||||||||||
|
Application Data (inches in millimeters) |
A | C | D | F | G | H | L | M | P | Q | R | W | X | AA | BB | CC | DD | NN |
| 8.25 | 69 | 2.50 | 2.0025 | 3.6240 | .25 | 3/8×3/16 | 4.50 | 3/4-16 | 1.437 | 4.44 | 7.00 | 8.50 | 1/2-13 | 5.00 | 5/8-11 | 8.25 | .593 | |
| (15.06) | ||||||||||||||||||
| 1.00DP | 1.13DP | 1.25DP | ||||||||||||||||
| (209.55) | (17.53) | (63.50) | (50.864) | (92.050) | (6.35) | (9.53×4.76) | (114.30) | (36.50) | (112.78) | (177.80) | (215.90) | (63.50) | (127.0) | (28.7) | (209.55) | (31.75) | ||
| Test parameters | greatest pressure | The maximum amount of leakage | ||||||||||||||||
|
CUBIC IN.PER MIN.AT 3000 PSL CC/min (206.9 BAR) |
CUBIC CM.PER MIN.AT 3000 PSL CC/min (206.9 BAR) |
|||||||||||||||||
| 50(3.44) | 1V | 2V | 1V | 2V | ||||||||||||||
| 18.31 | 19.5 | 300 | 320 | |||||||||||||||
ML-type plum-shaped flexible coupling(ML1-ML13)
Introduction
ML-type plum-shaped coupling in line with national standards GB5272-85, used in a variety of mechanical connection two concentric shaft drive, with a larger compensation for the two-axis relative offset, cushioning, shock absorption, oil, air aging resistance, wear Such as performance, reasonable structure, easy maintenance, less parts, adaptability, long service life, a working temperature of 35C to 80C, short-term working temperature up to 100C, delivering nominal torque of 16N.m to 25000N.m.
The middle of the elastic parts can be used according to the requirements of the selection of a variety of hardness polyurethane rubber, cast nylon elastomer and other materials, the use of precision cast iron shaft cast iron material for the HT300.
Shaft hole type cylindrical (Y), round push (Z) and short cylindrical (J), shaft hole and keyway type and size according to the national standard GB3852-83 "coupling shaft hole and keyway type and size" The provisions of processing.
NL type internal tooth shape flexible coupling graph and symbol
ML type plum-shaped flexible coupling structure and order marking method
| Model |
Allowable torque (N.m) |
Permission to change the model (r/min) |
Main dimensions | Permissible displacement |
Moment of inertia Kg/㎡ |
weight kg |
||||||||||
| d1,d2,dz | Y-type | J,Z-type | L0 | D | D1 | do | h | s | Axial | Radial | Angle | |||||
| L | L1 | △X | △Y | △α | ||||||||||||
| ML1 | 45 | 15300 | 12,14 | 32 | 27 | 80 | 50 | 40 | 48 | 12 | 2 | 1.2 | 0.5 | 2° | 0.014 | 0.8 |
| 16,18,19 | 42 | 30 | 100 | |||||||||||||
| 20,22,24 | 52 | 38 | 120 | |||||||||||||
| ML2 | 200 | 10900 | 22,22,24 | 52 | 38 | 127 | 70 | 50 | 68 | 18 | 2.5 | 1.5 | 0.8 | 2° | 0.075 | 2.1 |
| 25,28 | 62 | 44 | 147 | |||||||||||||
| 30,32 | 82 | 60 | 187 | |||||||||||||
| ML3 | 280 | 9000 | 22,24 | 52 | 38 | 128 | 85 | 60 | 82 | 18 | 3 | 2.0 | 0.8 | 2° | 0.178 | 3.2 |
| 25,28 | 62 | 44 | 151 | |||||||||||||
| 30,32,35,38 | 82 | 60 | 188 | |||||||||||||
| ML4 | 400 | 7300 | 25,28 | 62 | 44 | 151 | 105 | 75 | 100 | 20 | 3.5 | 2.5 | 0.8 | 2° | 0.412 | 5.5 |
| 30,32,35,38 | 82 | 60 | 191 | |||||||||||||
| 40,42 | 112 | 84 | 257 | |||||||||||||
| ML5 | 710 | 6100 | 30,32,35,38 | 82 | 60 | 197 | 125 | 90 | 122 | 25 | 4 | 3.0 | 1.0 | 1.5° | 0.73 | 7.8 |
| 40,42,45,48 | 112 | 84 | 257 | |||||||||||||
| ML6 | 1120 | 5300 | 35*,38* | 82 | 60 | 203 | 145 | 105 | 140 | 30 | 4.5 | 3.0 | 1.0 | 1.5° | 1.85 | 11.7 |
| 40*,42*,45,48,50,55 | 112 | 84 | 263 | |||||||||||||
| ML7 | 2240 | 4500 | 45*,48*,50,55 | 112 | 84 | 265 | 170 | 130 | 166 | 30 | 5.5 | 3.5 | 1.0 | 1.5° | 3.88 | 19 |
| 60,63,65 | 142 | 107 | 325 | |||||||||||||
| ML8 | 3550 | 3800 | 50*,55* | 112 | 84 | 272 | 200 | 155 | 196 | 35 | 6.5 | 4.0 | 1.5 | 1.5° | 9.22 | 33 |
| 60,63,65,70,71,75 | 142 | 107 | 332 | |||||||||||||
| ML9 | 5600 | 3300 | 60*,63*,65*,70,71,75 | 142 | 107 | 334 | 230 | 180 | 225 | 35 | 7.5 | 4.5 | 1.5 | 1° | 18.95 | 54 |
| 80,85,90,95 | 172 | 132 | 394 | |||||||||||||
| ML10 | 9000 | 2900 | 70*,71*,75* | 142 | 107 | 344 | 260 | 205 | 255 | 45 | 7.5 | 5.0 | 1.5 | 1° | 39.68 | 78 |
| 80*,85*,90,95 | 172 | 132 | 404 | |||||||||||||
| 100,110 | 212 | 167 | 484 | |||||||||||||
| ML11 | 12500 | 2500 | 80*,85*,90*,95* | 172 | 132 | 411 | 300 | 245 | 295 | 50 | 8.5 | 5.0 | 1.8 | 1° | 73.43 | 115 |
| 100,110,120 | 212 | 167 | 491 | |||||||||||||
| ML12 | 20000 | 2100 | 90*,95* | 172 | 132 | 417 | 360 | 300 | 356 | 55 | 9 | 5.0 | 1.8 | 1° | 178.45 | 206 |
| 100*,110*,120*,125* | 212 | 167 | 497 | |||||||||||||
| 130 | 252 | 202 | 577 | |||||||||||||
| ML13 | 25000 | 2000 | 100*,110*,120*,125* | 212 | 167 | 497 | 400 | 335 | 391 | 55 | 9 | 5.0 | 1.8 | 1° | 208.75 | 235 |
| 130*,140* | 252 | 202 | 577 | |||||||||||||
Ordering mark method
| Example 1: ML4 plum-shaped flexible coupling | Example 2: ML3 plum-shaped flexible coupling | ||||
| Drive shaft: Y-axis hole, A keyway,d1=30,L1=82 | ML4 | YA30×82 | Drive shaft: Z-axis hole, A keyway,d1=30,L=60 | ML3 | ZA30×60 |
| Driven end: Y-axis hole, A-type keyway,d2-42,L2=112 | YA42×112 | Driven end: Y-axis hole, B-type health slot,d2=25,L=62 | YB25×62 | ||
Products
Messages
Contact us
Mobile phone network
Copyright © 2018 Nantong Gaoye Heavy Industry Co.,Ltd. 编号：苏ICP备05027703号 Powered by www.300.cn